The demands of modern day construction are not limited to quality and cost, since time can be a key issue and is considered by some to be one of the most important aspects of a project. During the construction process of a project there are several related stages that follow a strict and unalterable sequence that directly affects the amount of time required by a project, and as a consequence has a direct effect on the contractor’s costs. The process of plastering or as it is technically known mortar coating, of indoor and outdoor walls and ceilings, is one of the phases or stages previously mentioned. There are two methods for preparing and applying the plaster mixture, the conventional method and the industrialized method. The industrialized method is relatively new in Occident, but it has been the principal method used in Europe by most contractors for several decades. This method accelerates the time it takes to prepare and apply the plaster mixtures making it 3 to 5 times faster than the conventional method, with a savings of up to 50% per square yard of applied plaster. These savings pertain only to the preparation and application of the mixtures, and do not include the additional potential savings of project time that could double these savings. The key to this method and to the savings for the contractor stems from the fact that it is an industrialized system, which means that you work with a superior quality plaster mix, an unequaled surface finish, a virtually instantaneous preparation of the mix, a continuous flow of mix, and an application by means of a plastering equipment that quickly covers surfaces. In this manner, construction workers and their assistants can complete 3 to 5 times more square areas of plastering a day, reducing the days needed for this work and resulting in savings for the project, and therefore, for the contractor. The industrialized mortar products of Ecológica Carmelo provide a solution with alternatives that include plastering mix, structural mortar mix, floor topping mix, self-leveling mix, general purpose mortar, polymer modified thin-set mortars and concrete resurfacing compounds. All of these alternatives offer economic advantages to the contractor and a cleaner environment for the project, and they diminish thecompletion time of the project.
Advantages of the Industrialized Mortar System:
Mixing Sprayable Plasters / Renders, Masonry, Self-leveling, Brick-laying and Thick bed mortars.
A significant increase in productivity
Quality is assured.
Mix is virtually ready in an instant
Reduction in waste and loss of material
No need to stock individual materials
Better material inventory control
Environmentally Friendly Material Conveying
System: - No dust emissions - No scattering of waste to the environment by surface water runoffs
Available equipments: Free-fall or Pressurized vertical silo (22 Mt2)
Mtec Application Equipment
Technology for better Building: Render Mortar or Cement Plaster Application Machines for walls and Ceilings
Technology for better Building
M-Tech Duo Plus:
Mixer D30 is our robust all-rounder for processing dry mortar products with a granularity for up to 6 mm. It is found on numerous building sites throughout the world and rationalizes tasks such as bricklaying and the processing of fine concrete or screeds.
The dual mixing system with two way mixing plus the patented sump principle. The two separate wet mixing chambers of the duo-mix plus guarantee top quality mortar, an even mix that is productive and free of cracks. All the usual trade renders such as cementitious floor screeds can be processed. We can offer relevant rebuild kits for special
M-tec Mono Mix:
With its revolutionary technology, the M300 marks the start of a new generation of mixing pumps. The “trick” with this new technology is our latest patented mixing principle, which allows the material to be blended perfectly and also ensures permanent consistency of the material. This means that the pump does not have to perform any additional mixing tasks and can concentrate on its core function-pumping.
The m-tec mono-mix - the adaptable mixing pump in 230 V for all machine applicable internal and external renders or adhesives and backing coats based on gypsum, lime-gypsum or lime-cement.
The new m-tec P50 is a powerful pump for processing pumpable products with a granularity of up to 8 mm. Thereby the P50 is mainly used for processing of mortar, concrete, plasters or fine coats as well as floor screeds. The pump P50 is available in different designs, suitable for the different applications with an output of up to 140 l/min.
With its revolutionary technology, the M300 marks the start of a new generation of mixing pumps. Pumps have long been used as dosers and mixers too, but the M300 can finally concentrate on its core function: pumping. The trick with this new technology is our patented mixing principle, which allows the material to be blended perfectly and also ensures permanent consistency of the material.
The m-tec speedy MP is an easy-to-handle pump for processing soft materials or pumpable products such as structured or decorative renders with a granularity of up to 2 mm. It is mainly used to pump creative decorative materials, fillers, key coats or primers.